320427 ECXV25 25' x 5" x .125" Vanguard Series Aluminum Flagpole, Clear Anodized

Internal Halyard Cam Action Cleat Aluminum Flagpoles with Stationary Truck (Standard) • Option to upgrade to Revolving Truck • Cam Action Cleat provides an economical alternative to winch-operated systems • 20' - 40' Height • Ground set, cone tapered

$2,220.00 $1,887.00   15% OFF!

This item qualifies for Free Shipping when you spend over $100

Vanguard Series Standard Accessories

  • Gold anodized aluminum ball ornament
  • Cast aluminum stationary truck
  • Nylon wire center halyard
  • Swivel flag snaps w/vinyl snap covers
  • Retainer ring and counterweight
  • Stainless steel quick link
  • Cam action cleat (located inside the flagpole behind a lockable access door)
  • Spun aluminum flash collar
  • Galvanized steel foundation sleeve

Note: 5" diameter poles are supplied with a hinged access door and frame unit. Other sizes are supplied with a removable access door (not hinged) which is attached to a frame plate that is welded to the inside of the pole providing a smooth exterior finish.

Ground Set Cone Tapered Aluminum (6063-T6) Flagpoles

General Information

Our cone tapered ground set aluminum flagpoles are precision fabricated from new, 6063-T6 tubing utilizing the industry's most sophisticated manufacturing processes. The conical portion tapers approximately 1" in every 5-1/2 feet. Poles with overall lengths of less than 38'6" are shipped in one piece. Longer lengths are shipped in sections and will be factory fitted with a self-aligning sleeve which requires no field welding. Upon proper assembly a hair-line joint will occur. All poles are double spiral wrapped with protective paper and shipped in a hard fiber tube. All foundation dimensions listed in this catalog are intended for general guidelines only in good, firm, dry soil. It is recommended to consult and engineer for specific foundation dimensions suited to your exact location.

Standard Finishes

All flagpole shafts are highly polished with fine grain aluminum oxide cloth resulting in a high quality, deep satin luster finish. This finish represents the ultimate in architectural finishes for aluminum flagpoles. The elegant, soft sheen remains maintenance free. The following anodized finishes are available as standard colors. Note: For bronze, dark bronze #313 is supplied unless otherwise specified.

Bronze #311
Bronze #312
Bronze #313
Black (#335)
BLACK (#335)

"WARNING" - The flagpole shaft will stain if allowed to remain in contact with wet or damp wrappings. If there is any sign that the shaft or its shipping tube has come in contact with water during shipment, remove it from the tube and unwrap immediately. If the shaft is to be stored outdoors, it must be stored unwrapped, out of the tube, and off the ground. If the shaft is to be stored indoors, it may be left in the wrappings and the tube, provided that it shows no sign of having been exposed to moisture and that it will not be exposed to moisture during storage.


"CAUTION" - Extreme care must be exercised when installing flagpoles near overhead power lines or when digging in the vicinity of buried cable or piping. Contact your local authorities before any digging.


The map below shows the maximum steady wind expected at an elevation of thirty feet above ground level within a fifty year period of recurrence. Areas with the same maximum constant or steady wind speed are indicated.

PLEASE NOTE: Recommended flag sizes do not represent a warranty that the flag size shown may be safely flown in all wind speeds. Personal injury, flagpole damage or property damage can occur when flying over sized flags and banners or flying flags in higher winds than recommended.

Because wind speeds are usually not constant, and gusts are involved, flagpoles (both flagged and unflagged) are listed in this catalog with a constant wind speed and a 1.3 gust factor.

Flagpoles and their associated wind speeds listed assume that ten percent of the overall length of the flagpole is buried per or recommendations at or near ground level. Special engineering may be required for other applications such as wall or roof mounted flagpoles. Contact us for a prompt response regarding any situation that may require special engineering.

Design of safe flagpoles requires knowledge of the loads to which they will be subjected. Principal load acting on flagpoles is wind load and that load must be carefully determined. Maximum wind speeds to which flagpoles are exposed depend on geographical location, whether or not it is in the center of a large city, a small town's outskirts, seashore, at ground level or on the roof of a high building. Wind speeds generally are higher along coastal areas than inland. They are also higher in open country than in the center of cities. Wind speed also becomes greater as height above ground increases. Wind exerts a force on the pole as well as the flag, thus both loads must be added to determine total load. Flags of different sizes are designed to be flown from different poles.

It's important that flagpoles be selected which are capable of supporting the largest flag intended to be flown in the highest wind speed to which it will be subjected. Loads on flagpoles are resisted by the mounting foundation, roof, or wall to which it is secured.

Brand Eder Flag Manufacturing Co. Eder Flag Manufacturing Co.
Flagpole Model Series / Type Vanguard - Internal Cam Cleat
Halyard Type Rope Halyard
Flagpole - Exposed Height 25 Feet
Butt Diameter 5"
Wall Thickness .125" or 1/8"
Color Clear Anodized
Ball Ornament 5" Gold Anodized (Standard)
Access Door Type Hinged Access Door and Frame Unit
Overall Length 27'
Top Diameter 3"
Number of Sections 1
Max Wind Speed w/ Flag 104 mph
Max Wind Speed No Flag 144 mph
Suggested Flag Size 4' x 6'
Flagpole Truck Cast Aluminum Revolving Truck
Mounting Option PVC Foundation Sleeve
Weight 139.0 lbs.

Replacement Parts

More Products you might like...

You might also be interested in...

People who bought this item also bought...

Related Resources